More info
Fluke Networks LIQ-100 LinkIQ Network Tester
- Find maximum cabling speed (Up to 10 Gb/s)
- Install and troubleshoot PoE devices via Switch Negotiation and PoE Load Test
- Identify connected switch information (Switch Name, Port Number, and VLAN)
- Document work through LinkWare™ PC
- Generate analog or digital tones compatible with IntelliTone™ Probe (not included) or Pro3000™ (not included) to assist in locating cables in wall or telecommunications room
- Blink Port light on switch to help identify connected switch port
- Compatible with MicroScanner™ PoE Remote Identifiers for Ethernet outlet identification
- Touch sensitive gesture-based display
- Rechargeable Li-Ion battery
- Easy Feature and Network Testing Upgrades via USB-C via LinkWare™ PC
- Charging via standard USB-C port
- Battery type: Lithium-ion, 3.6 V, 6400 mAh
- Battery life: 8 hours typical
- Battery charge time: 4.5 hours
- Battery charging temperature range: 0 °C to +40 °C
- Power adapter input: 100 to 240 VAC ±10%, 50/60Hz
- Power adapter output: 15 VDC, 2 A maximum; Class II
- Host interface: USB type C
- Display: 800 x 480 color capacitive multi-touch
- Operating temperature: 0°C to 45°C
- Storage temperature: -20°C to 50°C (-4°F to 122°F)
- Operating relative humidity: 0 % to 90 %, 0°C to 35°C; 0 % to 70 %, 35°C to 45°C
- Operating altitude: 4,000 m; 3,200 m with ac adapter
- Vibration: Random, 2 g, 5 Hz-500 Hz
- Drop: 1 m drop, 6 sides
- Diagnostic protocols: Link Layer Discovery Protocol (LLDP), Cisco Discovery Protocol (CDP), Fast Link Pulses (FLP)
- Nearest device diagnostics (if available through diagnostic protocols): Switch Name, Port Number, VLAN Name, Advertised Data Rates, Advertised Duplex
- Power Over Ethernet (PoE) compatibility: IEEE 802.3af/at/bt, Hardware negotiation with signature resistance, Software negotiation with LLDP/CDP
- Power Over Ethernet (PoE) diagnostics: Advertised Power Class (0-8), Advertised Available Power, Powered Pairs, Diagnostics for Single and Dual signatures
- Power Over Ethernet (PoE) measurements: Loaded Voltage (V), Loaded Power (W)
- Port blink: Blink light of connected port
- Test port: Shielded 8-pin modular jack accepts 8-pin modular (RJ45) plugs
- Commissioning autotests: 10GBASE-T, 5GBASE-T, 2.5GBASE-T, 1000BASE-T, 100BASE-TX, 10BASE-T, Wire map Only; test Speed: 6 seconds for lengths < 70 m
- Cable types: Balanced twisted-pair cabling; Unshielded twisted-pair; Screened twisted-pair; 2-pair and/or 4-pair
- Wire map-only tests: Document wire map, Length of each pair, Diagnose split pairs, User selectable T568A or T568B, User selectable crossover settings (Straight through, Half-crossover, Full-crossover). Test speed: 1 second for lengths < 120 m
- Length (Maximum): 305 m (1000 ft)
- Nominal velocity of propagation (NVP): User settable
- Remote ID locators: Use remote ID terminations to identify up to 7 unique ports or office outlets
The Fluke Networks LIQ100 LinkIQ™ Cable + Network Tester is the testing solution to verify cable performance up to 10 Gb/s and solve network connectivity problems. LIQ-100 validates cable performance using frequency-based measurements and provides distance to fault information along with a wire map of the cable under test. The LIQ-100 also performs nearest switch diagnostics to identify key network issues and validate switch configuration eliminating the need of using another device. Additional features include Analog and Digital Toning, Port Blink, 802.1x authentication, Remote Office Locators, and the ability to manage results via LinkWare™ PC.
Cable Testing You Trust
The LIQ-100 is capable of measuring lengths up to 1000 feet (305 m) and provides distance to faults such as opens, shorts, and unterminated cable. Using the remote ID allows for a complete wire map of the cable pairs which helps identify miswired and split pairs. The primary cable testing feature of LIQ-100 is the cable performance test which qualifies the cabling bandwidth from 10BASE-T to 10GBASE-T (10 Mb/s up to 10 Gb/s). It performs these tests via frequency-based measurements. Using IEEE-standards-based measurements ensures that tested links meet performance requirements as opposed to transmission testers which only prove that the specific test devices can communicate over the link.